BOSCH ERROR CODES/470 CODES/10 APPLIANCE TYPES
Bosch appliance error codes
Bosch dishwasher and BSH source files exist, with a homeowner-ready E15 guide already published.
Written by Dmitriy Sukhov · Founder, Express Xpert Appliance RepairUpdated July 2026
JUMP TO
01 / 10
Bosch dishwasher codes
11 codes documented with safe checks and repair guidance for South Florida homes.
- E15 — Leak protection or water in base pan
- E14 — Flow-meter filling fault (water fill not being counted)
- E0 — Bosch Dishwasher E0 error code explained
- E1 — Problème de chauffage
- E3 — Bosch Dishwasher E3 error code explained
- E4 — Water points cannot be positioned
- E5 — Niveau de sécurité atteint
- E6 — Aqua sensor (even if there is no aqua sensor)
- E7 — Bosch Dishwasher E7 error code explained
- E7101 — Connection of Home
- R5 — Bosch Dishwasher R5 error code explained
02 / 10
Bosch wall oven codes
76 codes documented with safe checks and repair guidance for South Florida homes.
- E0537 — Touch-control calibration error
- E010D — Control module lost the mains-frequency signal
- E8030 — Cavity temperature too high with the door unlocked
- AV1 — Bosch Wall Oven AV1 error code explained
- E010A — Plausibility check
- E010B — No parameters No parameters Check/program the Control Module (CPM) set of charac
- E010C — Permanent interruption Mains voltage interrupted, most frequent cause is
- E0110 — General and/or unknown
- E0111 — Communication error
- E0113 — Communication error
- E0502 — Data storage error
- E0504 — RTC communication error Faulty RTC module Replace the Operating Module and after
- E0510 — Mult Media Board (MMB)
- E0511 — Communication error
- E0532 — Button continuously actuated
- E0533 — Button permanently pressed
- E0534 — Error in touch calibration when
- E0535 — Error in touch calibration during
- E0536 — Error in touch calibration when
- E0538 — Error in touch calibration when
- E0539 — Error in touch calibration in the
- E100B — Thermistor discontinuity ER1 Oven thermistor is not detected
- E100C — Thermistor discontinuity ER4 Oven thermistor short circuit detected
- E1201 — ROM or Flash Check Error
- E1202 — Data storage error
- E1205 — DBus – connection error in the
- E1210 — General and/or unknown
- E1301 — Magnetron thermistor
- E1302 — Magnetron thermistor
- E5000 — General error in the steam
- E5002 — ROM or Flash Check Error
- E5004 — Incorrect variant code Incorrect or no variant code (VC) Check the current varia
- E5010 — General communication error
- E5011 — Communication error
- E5111 — Bosch Wall Oven E5111 error code explained
- E5112 — Polarity check during self-test
- E5114 — E-Fast (temperature sensor in
- E5115 — E-Fast (temperature sensor) in
- E5116 — E-Fast (temperature sensor in
- E5121 — Message text in the appliance display: “Tank empty” appears ........... 20
- E5123 — Evaporator gets not full
- E5133 — Water tank fill level sensor Water tank sensor not working correctly
- E5135 — E-Fast (temperature sensor)
- E6000 — General and/or unknown
- E6100 — General and/or unknown
- E6200 — General and/or unknown
- E6300 — General and/or unknown
- E6400 — Venting flap motor fault
- E6501 — Panels motor error
- E6900 — General error door motor Failure of the door motor electronic
- E6901 — Door motor overload The door motor detected overload
- E6902 — Door motor blocked Door is blocked or the position of the electrical door hinge
- E6903 — Door motor over temperature Door motor is overheated, maybe after a longer opera
- E6904 — Door motor referencing not
- E6906 — Door motor power unit reference
- E6907 — Door motor power unit failure
- E6908 — Door motor power unit failure
- E6909 — Door motor power unit current
- E690A — Door motor encoder failure
- E690B — Door motor encoder failure
- E6910 — Door motor communication error
- E7101 — Home Connect data is missing Home Connect data was not programmed, e. g. after
- E8020 — Bosch Wall Oven E8020 error code explained
- E8401 — Oven temperature sensor
- E8402 — Oven temperature sensor
- E8601 — Lambda probe (baking sensor)
- E8602 — Lambda probe (baking sensor)
- E8603 — Lambda probe (baking sensor)
- E8604 — Lambda probe (baking sensor)
- ECC10 — General communication error Faulty DBus 2 communication
- F1001 — Temperature monitoring of
- F1002 — Temperature monitoring of
- F1006 — Inverter error H97
- F1008 — Inverter error H99
- F5211 — Pyrolysis can not be started
- F8403 — Oven temperature sensor fixed
03 / 10
Bosch steam oven codes
2 codes documented with safe checks and repair guidance for South Florida homes.
04 / 10
Bosch cooktop codes
72 codes documented with safe checks and repair guidance for South Florida homes.
- F9 — PiezoControl touch-control data fault
- E0517 — Internal module communication error
- F8 — Automatic operating-time limit reached
- DE — Demo mode is active
- E/LC — 1.10 Common errors when connecting the mains cable to the hob
- E0301 — Incorrect or faulty firmware: the control and
- E0302 — Error in the microcontroller's internal memory
- E0308 — The fan is not working
- E0312 — Error in the additional communication between
- E0315 — Error in the communication protocol between the
- E0322 — Overheating of the electronics of the control and
- E0323 — Overheating of the electronics of the control and
- E0331 — Error in the supply voltage synchronization
- E0332 — Error when checking control and power module
- E0335 — Error when checking control and power module
- E0337 — Fault in the additional inductor temperature
- E0339 — Error when checking control and power module
- E0341 — Error when checking control and power module
- E0342 — Error when checking control and power module
- E0343 — Error when checking control and power module
- E0344 — Error when checking control and power module
- E0345 — Error when checking the control and power
- E0346 — Error when checking control and power module
- E0500 — E1 Defective unit / General or
- E0501 — E1 ROM or FLASH checksum error
- E0502 — Error in the microcontroller's internal memory
- E0503 — Incorrect software version of the User Interface. Wrong spare part. Replace th
- E0509 — Error in the Hall sensor for the rotary knob in
- E0510 — F0 Communication error / General
- E0513 — DBUS2 communication failure between control
- E0516 — See E0513 See E0513 See E0513
- E0520 — E9 Overheating error Defective temperature sensors Replace the user interface mo
- E0521 — F2 Overheating > 105ºC Temperature sensors have reached
- E0522 — F4 Overheating > 120ºC Temperature sensors have reached
- E0523 — F5 High temperature warning Temperature sensors have reached
- E0531 — Internal error in the User Interface sensors
- E0532 — E6 Permanent pressing (no rotor
- E0612 — Error in the communication between User
- E0615 — Object on the control panel. The control panel is damp or an object covers
- E0711 — Error communication between right ZoneLight
- E0804 — Front LED misbehaviour. Faulty LED
- E0906 — Error communication between LED driver and
- E0911 — Error communication between right ZoneLight
- E0922 — Overtemperature error on ZoneLight module
- E0923 — Overtemperature error on ZoneLight module
- E2430 — Fault in the inductor temperature sensor (NTC)
- E2431 — Fault in the inductor temperature sensor (NTC)
- E2432 — Fault in the inductor temperature sensor (NTC)
- E2433 — Fault in the central inductor's temperature
- E7010 — Fault in the communication Home Connect
- E7015 — Overheating of the Home Connect board (COM
- E7101 — Incorrectly or missing coding of the Touch
- E8203 — Overheating of the cooking sensor
- E8204 — Cooking sensor battery almost worn out
- E8205 — The cooking sensor has lost the communication
- E8206 — Error checking cooking sensor components
- E8208 — Overheating of the Bluetooth board (YL245)
- E9032 — Undercurrent in power board in corresponding
- E9300 — Supply voltage below the expected value
- E9310 — Supply voltage above the expected value
- E9311 — Supply voltage much higher than expected value
- F0247 — Error when checking control and power module
- F0323 — Overheating of the electronics of the control and
- F0346 — Error when checking PDS system (pot detection
- F1 — TouchControl NTC fault (Gaggenau only) NTC of the intrinsic temperature monito
- F2 — TouchControl disconnected due to
- F2520 — Overheating of the inductor
- F3 — Cooking sensor fault
- F4 — TouchControl disconnected due to
- F5 — High temperature warning A hot pot is placed on or close to the User
- F6 — Temperature rise at sensor doesn’t
- F7 — Frying sensor fault
05 / 10
Bosch front-load washer codes
1 code documented with safe checks and repair guidance for South Florida homes.
06 / 10
Bosch appliance codes
20 codes documented with safe checks and repair guidance for South Florida homes.
- F111 — Runaway Oven temperature 585°F Latch unlocked 5 sec
- F113 — Runaway Oven temperature 950°F Latch locked 5 sec
- F121 — Stuck key in the membrane switch layer Always 1 min
- F125 — Cancel key circuit problem Always 1 min
- F141 — Slave micro not functioning Always 1 min
- F151 — Eeprom failure or communication circuit failure Cook or clean programmed 1 sec
- F153 — User Interface too hot Always 1 sec
- F154 — Power Board too hot Always 1 sec
- F155 — Cook profile corrupted in EPROM Cook or clean programmed 1 sec
- F170 — Pow er Failure Always 2 ms
- F190 — Power over voltage At power on
- F200 — Time out and stop function During Production test
- F210 — Range exceeded safe test limits During Service test mode 200°F
- F31 — Oven temperature sensor failure Cook or clean programmed 20 sec
- F33 — Warming Drawer Sensor Failure When W. Drawer is active 20 sec
- F3F3 — Meat probe not there or incorrect
- F41 — Motorized latch will not lock Latch should be locked 1 min
- F43 — Motorized latch will not unlock Latch should be unlocked 1 min
- F45 — Motorized Latch both locked and unlocked Always 1 min
- F7 — Shorted Oven Sensor Or
07 / 10
Bosch dryer codes
5 codes documented with safe checks and repair guidance for South Florida homes.
- P10 — Operating Hours ................................................................
- P11 — Operating Cycles ...............................................................
- P14 — Factory test ...................................................................
- T2 — (Heating element) Thermocouple Open or Short Circuit None E:18 Check temperature
- T4 — (Drum exit) Thermocouple Open or Short Circuit None E:17 Check temperature senso
08 / 10
Bosch range codes
171 codes documented with safe checks and repair guidance for South Florida homes.
- AC — E0x33, E0x34 and E0x35 update
- DE — Demo mode is active
- E/LC — X E0612 update. Necessary information for problem analysis in f
- E000 — Bosch Range E000 error code explained
- E005 — Loss of communication between user
- E009 — E309 ROM-check error in user interface
- E011 — Continuous pushing of a single key
- E0301 — Incorrect or faulty firmware: the control and
- E0302 — Error in the microcontroller's internal memory
- E0308 — The fan is not working
- E0312 — Error in the additional communication between
- E0315 — Error in the communication protocol between the
- E032 — Continuous pushing of multiple
- E0322 — Overheating of the electronics of the control and
- E0323 — Overheating of the electronics of the control and
- E0331 — Error in the supply voltage synchronization
- E0332 — Error when checking control and power module
- E0333 — Error when checking control and power module
- E0335 — Error when checking control and power module
- E0337 — Fault in the additional inductor temperature
- E0339 — Error when checking control and power module
- E0341 — Error when checking control and power module
- E0342 — Error when checking control and power module
- E0343 — Error when checking control and power module
- E0344 — Error when checking control and power module
- E0345 — Error when checking the control and power
- E0346 — Error when checking control and power module
- E044 — Touch control module (TCM)
- E050 — Rotary encoder switch short to
- E0500 — Error in the User Interface. Undetermined internal error. Replace the User Int
- E0502 — Error in the microcontroller's internal memory
- E0503 — Incorrect software version of the User Interface. Wrong spare part. Replace th
- E0509 — Error in the Hall sensor for the rotary knob in
- E0513 — DBUS2 communication failure between control
- E0516 — Communication fault with cooking sensor
- E0521 — User Interface disconnected due to overheating
- E0522 — User Interface disconnected due to overheating
- E0523 — High temperature warning. A hot pot is placed on or close to the User
- E0531 — Internal error in the User Interface sensors
- E0612 — Communication error between the user interface
- E0615 — Object on the control panel. The control panel is damp or an object covers
- E0711 — Error communication between right ZoneLight
- E0804 — Front LED misbehaviour. Faulty LED
- E0906 — Error communication between LED driver and
- E0911 — Error communication between right ZoneLight
- E0922 — Over temperature error on ZoneLight module
- E0923 — Over temperature error on ZoneLight module
- E1 — Bosch Range E1 error code explained
- E10 — Control bd Checksum error Replace dreefs bd
- E106 — Door latch does not lock
- E107 — Door latch does not unlock
- E11 — Latch problem Will not clean Replace latch in affected oven
- E115 — Unlocked cavity temperature too
- E116 — Bosch Range E116 error code explained
- E118 — Cooling fan speed too low Fan speed has been sensed as too low
- E12 — Latch problem Will not clean Replace latch in affected oven
- E122 — Meat probe sensor temperature
- E123 — Meat probe sensor temperature
- E126 — Bosch Range E126 error code explained
- E13 — Latch problem Latch does not run Check for voltage to latch motor
- E2 — G & K Cook or Clean mode runaway (temp >635 °F). Clean mode runaway
- E2430 — Fault in the inductor temperature sensor (NTC)
- E2431 — Fault in the inductor temperature sensor (NTC)
- E2432 — Fault in the inductor temperature sensor (NTC)
- E2433 — Fault in the central inductor's temperature
- E3 — A & H Open oven temperature sensor (>5000 Ω)
- E302 — Control module too hot
- E303 — Electronics Delta temperature too
- E305 — Loss of communication between TCM
- E310 — Data memory error in user
- E312 — Defective control module
- E314 — E414 Cancel / Off key error Oven operation will be stopped. Error
- E4 — A & H Shorted oven temperature sensor (<5000 Ω)
- E5 — K& D Control board too cold, too hot, or defective
- E6 — Selector switch Disables individual cook
- E7 — A & I Illegal temperature display. Turn off oven and try again
- E7010 — Fault in the communication Home Connect
- E7015 — Overheating of the Home Connect board (COM
- E7101 — Incorrectly or missing coding of the Touch
- E8 — Bosch Range E8 error code explained
- E8203 — Overheating of the cooking sensor
- E8204 — Cooking sensor battery almost worn out
- E8205 — The cooking sensor has lost the communication
- E8206 — Error checking cooking sensor components
- E8208 — Overheating of the Bluetooth board (YL245)
- E9 — Latch Latch motor may run but
- E9032 — Undercurrent in power board in corresponding
- E9300 — Supply voltage below the expected value
- E9310 — Supply voltage above the expected value
- E9311 — Supply voltage much higher than expected value
- F0247 — Error when checking control and power module
- F0249 — Error when checking control and power module
- F0323 — Overheating of the electronics of the control and
- F0346 — Error when checking PDS system (pot detection
- F1 — Meat probe not there or incorrect During Test / use
- F10 — Oven sensor open Open circuit Check sensor See note 1
- F11 — Oven sensor shorted Pinched wire Check sensor See note 1
- F111 — Runaway Oven temperatur e 585°F Latch unlocked 5 sec
- F112 — Runaway lower temperature
- F113 — Runaway Oven temperat ure 950°F Latch locked 5sec
- F114 — Runaway lower temperature
- F12 — Open meat probe Socket, wiring Check probe See note 2
- F121 — Stuck key in the membrane switch layer Always 1 min
- F123 — Keyboard disconnected
- F125 — Cancel key circuit problem Always 1 min
- F13 — Upper oven RTD not calibrated Always 10 seconds Message 1 Cancel
- F14 — Display board EEPROM error Oven Pr ogramming 5 tries Message 1 Cancel
- F141 — Slave micro not functioning Always 1 min
- F143 — Vcc open circuit on slave micro
- F145 — Sensor input on the slave micro
- F147 — Ground open circuit on the slave
- F15 — Relay bd sensor shorted Short circuit Replace relay bd
- F151 — Eeprom failure or communication circu it failure Cook or clean programmed 1 sec
- F153 — User Interface too hot Always 1 sec
- F154 — Power Board too hot Always 1 sec
- F155 — Cook profile corrupted in EEPROM Cook or clean Programmed 1 sec
- F16 — Catalyst sensor open Wiring Check sensor See note 3
- F17 — Catalyst sensor shorted Wiring Check sensor See note 3
- F170 — Power Failure Always 2 ms
- F19 — Power board Communication error Always 20 seconds Message 1 Cancel
- F190 — Power over voltage At power on
- F2 — User Interface disconnected due to overheating
- F20 — Function switch problems Open cable or switch Run diagnostics See note 4
- F200 — Time out and stop function Du ring Production test mode 110 sec
- F21 — Temperature switch not
- F210 — Range exceeded safe test lim its During Service test mode 200°F
- F22 — Push buttons don’t work Open cable or switch Run diagnostics See note 4
- F23 — Keyboard gain unstable
- F24 — Keyboard disconnected Always 20 seconds Message 1 Cancel
- F25 — Keys stuck Always 20 seconds Message 1 Cancel
- F2520 — Overheating of the inductor
- F26 — Keys moving/dropping out Always 20 seconds Message 1 Cancel
- F3 — Sensor problem Open or shorted sensor Check sensor
- F30 — Upper oven sensor shorted Always 20 seconds Message 1 Cancel
- F31 — Oven temperature sensor failure Cook or clean programmed 20 sec
- F32 — Upper oven over temperature while
- F33 — Upper oven over temperature while Non-Clean 20 seconds Message 1 Cancel
- F34 — Upper oven cooling fan over-speed or
- F4 — User Interface disconnected due to overheating
- F40 — Upper oven meat probe shorted Cooking 20 seconds Message 1 Cancel
- F41 — Upper oven meat probe not calibrated Always 10 seconds Message 1 Cancel
- F42 — Door switch Switch open while door
- F43 — Lower oven RTD not calibrated Always 10 seconds Message 1 Cancel
- F44 — Lower motorized latch will not
- F45 — Motorized Latch both locked and unlocked Always 1 min
- F46 — Lower oven latch both locked
- F5 — High temperature warning A hot pot is placed on or close to the User
- F50 — Upper oven door latch signal shorted low Always 1 minute Message 1 Cancel
- F51 — Upper oven door latch stuck unlocked Co oking/ Cleaning 1 minute Message 1 Cance
- F52 — Upper oven door position error Cooking/ Cleaning 1 minute Message 1 Cancel
- F53 — Upper oven door latch stuck locked Non-Clean 1 minute Message 1 Cancel
- F54 — Upper oven latch input shorted Cleaning 1 minute Message 1 Cancel
- F60 — Lower oven sensor shorted Always 20 seconds Message 1 Cancel
- F61 — Lower oven sensor open Always 20 seconds Message 1 Cancel
- F62 — Lower oven over temperature while
- F63 — Lover oven over temperature while
- F64 — Lower oven cooling fan over-speed or
- F7 — The control is reading a shorted key
- F70 — Lover oven meat probe shorted Cooking 20 seconds Message 1 Cancel
- F71 — Lower oven meat probe not calibrated Always 10 seconds Message 1 Cancel
- F72 — Base pan sensor Defective electronics Replace relay board
- F73 — Main water valve not
- F74 — Pressure switch stays
- F80 — Lower oven door latch signal shorted low Always 1 minute Message 1 Cancel
- F81 — Lower oven door latch stuck unlocked Cook ing/ Cleaning 1 minute Message 1 Cance
- F82 — Lower oven door position error Cooking/ Cleaning 1 minute Message 1 Cancel
- F83 — Lower oven door latch stuck locked Non-Clean 1 minute Message 1 Cancel
- F84 — Lower oven door latch input shorted Cleaning 1 minute Message 1 Cancel
- FC — Communication Error Detected by
- P26 — Bosch Range P26 error code explained
- T1 — Error (error displays)
09 / 10
Bosch refrigerator codes
38 codes documented with safe checks and repair guidance for South Florida homes.
- E0 — Compartment temperature sensor 1 open/short
- E01 — Bosch Refrigerator E01 error code explained
- E02 — Bosch Refrigerator E02 error code explained
- E06 — Sensor value of fridge comp. evaporator
- E07 — Sensor value of freezer comp
- E08 — Chiller compartment evaporator Check sensor
- E10 — Control module Data flash not compatible with software / memory
- E11 — Display module Replace DOM
- E20 — CM and DOM Communication error Replace CM
- E21 — IWD and DOM Replace IWD
- E3 — UIM communication error
- E30 — CM Timeout Replace CM
- E31 — Bosch Refrigerator E31 error code explained
- E40 — Ice maker NTC out of range/defect Ice maker NTC out of range/defect Check wiring
- E41 — Icemaker motor/gearbox Ice maker motor/gearbox defect Ice maker motor/gearbox de
- E43 — Communication to appliance CM error Communication to appliance CM error wiring c
- E44 — Water system defect Water system defect or wiring connect failed Water system de
- E46 — No temperature available for IWS Ice maker sensor out of range or defect Ice mak
- E47 — No feedback from hopper flap switch Switch defect/wiring connect failed Switch d
- E48 — No feedback from ICF switch ICF switch defect/ wiring connect failed ICF switch
- E6 — UIM memory error firmware
- FC — Freezer compartment
- L00 — Bosch Refrigerator L00 error code explained
- L01 — Bosch Refrigerator L01 error code explained
- L02 — Bosch Refrigerator L02 error code explained
- L03 — Bosch Refrigerator L03 error code explained
- L04 — Bosch Refrigerator L04 error code explained
- L05 — Bosch Refrigerator L05 error code explained
- L06 — Bosch Refrigerator L06 error code explained
- L07 — Bosch Refrigerator L07 error code explained
- L08 — Bosch Refrigerator L08 error code explained
- L09 — Bosch Refrigerator L09 error code explained
- L10 — Bosch Refrigerator L10 error code explained
- L11 — Bosch Refrigerator L11 error code explained
- L12 — Bosch Refrigerator L12 error code explained
- L13 — Bosch Refrigerator L13 error code explained
- L14 — Bosch Refrigerator L14 error code explained
- L15 — Bosch Refrigerator L15 error code explained
10 / 10
Bosch washer codes
74 codes documented with safe checks and repair guidance for South Florida homes.
- E01 — POWER CONTROL MODULE 1
- E010 — Bosch Washer E010 error code explained
- E011 — COMMUNICATION ERROR
- E012 — VARIANT CODING ERROR
- E013 — SOFTWARE - COMPONENT MISMATC H
- E050 — Bosch Washer E050 error code explained
- E051 — COMMUNICATION ERROR
- E053 — Bosch Washer E053 error code explained
- E060 — Bosch Washer E060 error code explained
- E0600 — SMM - general or undetermined error ............................. 10
- E062 — COMMUNICATION ERROR
- E07 — USER INTERFACE OSM
- E070 — Bosch Washer E070 error code explained
- E0720 — OSM touch sensor calibration error .................................. 13
- E0730 — OSM data missing or corrupted ........................................ 13
- E0800 — PSM general or undetermined error ................................ 14
- E0820 — PSM touch sensor calibration error .................................. 15
- E0830 — PSM data missing or corrupted ......................................... 15
- E102 — AGENT COMPARTMENT ERROR
- E121 — COMMUNICATION ERR OR
- E122 — Bosch Washer E122 error code explained
- E140 — Bosch Washer E140 error code explained
- E2 — Heating Systems / E20 -Heating Circuit 1
- E20 — Bosch Washer E20 error code explained
- E200 — GENERAL OR UNDETERMI NED ERROR
- E201 — Bosch Washer E201 error code explained
- E202 — NTC CONDENSER INLET
- E203 — NTC CONDENSER OUTLET DEFECT
- E206 — Bosch Washer E206 error code explained
- E301 — WATER FILLING TIME FOR COLD OR WA RM WATER EXCEEDED (C ONVENTIONAL PRESSURE SENO
- E302 — OVERFLOW LEVEL EXCEE DED
- E308 — DRAINING SYSTEM ERROR
- E31 — Bosch Washer E31 error code explained
- E310 — Bosch Washer E310 error code explained
- E311 — Bosch Washer E311 error code explained
- E33 — Bosch Washer E33 error code explained
- E330 — Bosch Washer E330 error code explained
- E34 — Bosch Washer E34 error code explained
- E341 — ERROR TURBIDITY SENSOR
- E35 — Bosch Washer E35 error code explained
- E351 — AQUA STOP ACTUATED
- E361 — Bosch Washer E361 error code explained
- E362 — BLDC DRAIN PUMP ERROR
- E370 — Bosch Washer E370 error code explained
- E382 — CIRCULATION PUMP ERR OR
- E6 — Drive Train (including driver electronics) / E38 - BLDC - Circulation Pump (incl
- E60 — BLDC1 (DRUM MOTOR)
- E600 — Bosch Washer E600 error code explained
- E601 — COMMUNICATION ERROR
- E602 — Bosch Washer E602 error code explained
- E603 — Bosch Washer E603 error code explained
- E71 — HOME CONNECT INTERFACE (HCI)
- E711 — COM - HOME APPLIANCE CONTROL SYST EM COMMUNICATION ERR OR
- E80 — Bosch Washer E80 error code explained
- E801 — Bosch Washer E801 error code explained
- E802 — Bosch Washer E802 error code explained
- E803 — Bosch Washer E803 error code explained
- E81 — Bosch Washer E81 error code explained
- E810 — Bosch Washer E810 error code explained
- E82 — Bosch Washer E82 error code explained
- E821 — COMMUNICATION ERROR
- E84 — Bosch Washer E84 error code explained
- E840 — UNIT DEFECT OR COMPONENT FAILURE
- E841 — COMMUNICATION ERROR
- E9 — External Impacts / E84 - 3D-Gen2 Sensor
- E90 — Bosch Washer E90 error code explained
- E901 — HIGH VOLTAGE / LINE FREQUENCY DEV IATION
- E902 — LINE FREQUENCY DEVIATION
- E920 — INCOMING WATER FLOW TOO LOW
- F20 — Bosch Washer F20 error code explained
- P16 — Bosch Washer P16 error code explained
- P17 — NOISE / P:17 (Factory noise test program) -
- P19 — Bosch Washer P19 error code explained
- P20 — Bosch Washer P20 error code explained
NEED HELP?
Stuck on a Bosch code?
If the code returns after the safe checks, the appliance likely needs internal testing. Express Xpert services Miami-Dade, Broward, and Palm Beach with same-day Bosch repair across all major appliance categories. See our dedicated Bosch repair page for costs and what repair involves.
Insured & bonded 90-day warranty 5.0 Google rating Same-day service